Oil and Gas
C15 ACERT™ Water-Cooled Mainfold Engine
-
Maximum Rating540 BHP
-
Displacement928 in³
-
Minimum Rating536 BHP
-
AspirationTurbocharged-Aftercooled
General Specifications
- Maximum Rating
- 540 BHP
- Displacement
- 928 in³
- Minimum Rating
- 536 BHP
- Aspiration
- Turbocharged-Aftercooled
- Flywheel and Flywheel Housing
- SAE No. 1
- Flywheel Teeth
- 113 (SAE 1)
- Stroke
- 6.7 in
- Bore
- 5.4 in
Emissions
- Emissions
- IMO Tier II Certified, Marine Tier 2 Certified, Marine Tier 3 Capable
Dimensions
- Length
- 80.18 in.
- Length
- 80.18 in
- Width
- 41.35 in.
- Width
- 41.35 in
- Height
- 55.65 in.
- Height
- 55.65 in
- Weight
- 3730.0 lb
- Weight
- 3730 lb
-
Air Inlet System
- Remote-mounted aftercooler with shutoff, 90° turbo inlet connection, 101.6 mm (4") hose connection with shutoff; separate circuit aftercooler with straight turbo inlet connection, 127 mm (5") hose connection
-
Control System
- Electronic governing, PTO speed control, programmable ratings, cold mode start strategy, automatic altitude compensation, power compensation for fuel temperature, programmable low and high idle and TEL, electronic diagnostics and fault logging, engine monitoring and protection system (speeds, temperature, pressure), J1939 broadcast (diagnostic, engine status and control)
-
Cooling System
- Thermostat and housing — outlet vertical; jacket water pump — gear-driven, centrifugal; RH front water pump inlet
-
Exhaust System
- Right rear turbo exhaust, watercooled turbine housing, carbon steel exhaust manifold — wet
-
Flywheels and Flywheel Housing
- SAE 1 flywheel housing standard, see price list for flywheel options
-
Fuel System
- Electronic unit injector; fuel priming pump — upward angled; engine-mounted secondary fuel filter, front-mounted fuel transfer pump — LH front; fuel sample valve — mounted on fuel filter base
-
Lube System
- Oil cooler; RH oil filter; rear sump 38 L oil pan; valve cover oil fill, optional front oil fill; oil gauges standard with LH and RH access; oil valve sampling on oil filter base; remote-mount oil filter kit
-
Mounting System
- Front support with mounting provision for LH or RH alternators
-
Power Take-Off
- SAE B options for SCAC and REMAC: single cylinder ATEX air compressor; dual cylinder air compressor, SAE B drive adapter; SAE A drive for REMAC
-
Front Engine Accessory Drive
- 3 v-groove standard — optional 4 and 5 groove 203.2 mm (8.0") diameter crankshaft, 17.5 mm (11/16") v-belt; optional v-belt or 8-groove accessory drive for 240.39 mm (9.46") diameter pulley; LH and RH mounting poly v-belt; CSA 24V 65 amp alternator — LH and RH mounting poly v-belt; variable fan heights and ratios with 3 and 4 groove fan drives (see Price List)
-
General
- Vibration damper, lifting eyes, automatic variable timing — electronic, electronic installation kit 70-pin connector (connectors, pins, sockets), literature GP Owner & Operator, paint
Mulchers: HM112 Standard Flow Mulcher 
Mulchers: HM115 Standard Flow Mulcher 
Material Handling: 4137 mm (163 in) Material Handling Arm, Fusion 
Material Handling: Material Handling Arm For Compact Products 
Material Handling: 3941 mm (155 in) Material Handling Arms – Loader 
Hammers: H215 S Hydraulic Hammer 
Hammers: H180 S Hydraulic Hammer 
Hammers: H190 S Hydraulic Hammer 
Hammers: H130 S Hydraulic Hammer 
Hammers: H160 S Hydraulic Hammer 
Hammers: H140 S Hydraulic Hammer 
Hammers: H110 S Hydraulic Hammer 
Hammers: H120 S Hydraulic Hammer 
Hammers: H115 S Hammer 
GC Hammers: H160 GC S Hammer 
GC Hammers: H180 GC S Hammer 
GC Hammers: H130 GC S Hammer 
GC Hammers: H120 GC S Hammer 
GC Hammers: H115 GC S Hammer