Piscataway Campus
732-885-5555
Bensalem Campus
877-726-7663

Land Mechanical Engines

C15 ACERT Land Mechanical Drilling Engine

  • Minimum Rating
    440.0 bhp
  • Minimum Rating
    440 BHP
  • Maximum Rating
    595.0 bhp
  • Maximum Rating
    595 BHP
Engine Specifications
Minimum Rating
440.0 bhp
Minimum Rating
440 BHP
Maximum Rating
595.0 bhp
Maximum Rating
595 BHP
Emissions
EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA
Emissions
EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA
Rated Speed
2100.0 RPM
Rated Speed
2100 r/min
Bore
5.4 in
Bore
5.4 in
Stroke
6.75 in
Stroke
6.75 in
Displacement
928.0 in3
Displacement
928 in³
Aspiration
Turbocharged-Aftercooled
Aspiration
Turbocharged-Aftercooled
Governor and Protection
ADEM A3
Engine Weight
2743.0 lb
Engine Weight
2743 lb
Oil Change Interval
250
Rotation
Counterclockwise
Oil Change Interval
250
Rotation from Flywheel End
Counterclockwise
Flywheel and Flywheel Housing
SAE No. 0 or SAE No. 1
Flywheel and Flywheel Housing
SAE No. 0 or SAE No. 1
Flywheel Teeth
136 (SAE 0), 113 (SAE 1)
Flywheel Teeth
136 (SAE 0), 113 (SAE 1)
Capacity for Liquids
Minimum Cooling System
5.5 gal (US)
Dimensions
Length
54.2 in
Length
54.2 in
Width
36.5 in
Width
36.5 in
Height
48.3 in
Height
48.3 in
  • Air Inlet System
    • Single turbocharger, mid-mounted, inlet 152.4 mm (6 in), hose connection
  • Control System
    • Electronic governing, PTO speed control
    • Programmable ratings
    • Cold mode start strategy
    • Automatic altitude compensation
    • Power compensation for fuel temperature
    • Programmable low and high idle and TEL
    • Electronic diagnostics and fault logging
    • Engine monitoring and protection system (speed, temperature, pressure)
    • J1939 Broadcast (diagnostic, engine status, and control)
  • Cooling System
    • Thermostats and housing — outlet vertical
    • Jacket water pump — gear-driven, centrifugal, RH
    • RH front water pump inlet
    • All plugs/fittings are STOR for lines gp water
  • Exhaust System
    • Exhaust manifold — dry
    • Front turbo exhaust
    • Full marmon connection, maximum load 10 kg for direct connection to turbo
  • Flywheels and Flywheel Housings
    • See Mandatory Options
  • Fuel System
    • MEUI system
    • Fuel filter, secondary, mid-mount (LH 2 micron high performance)
    • Fuel transfer pump, LH front
    • Fuel priming pump, LH mid-mount
    • Fuel sample valve, mounted on fuel filter base
  • Lube System
    • Crankcase breather — rear valve cover
    • Oil cooler — RH
    • Oil filter — RH
    • Oil pan — front sump
    • Oil filler — LH front
    • Oil dipstick — LH front
    • Oil pump
    • Oil valve sampling — on oil filter base
  • Mounting System
    • Front support (shipping only)
  • Power Take-Offs
    • Crankshaft pulley, 203.2 mm (8 in), 3 grooves 292.1 mm (11.5 in) 1 groove, all 15.9 mm (.63 in) width
    • Hydraulic pump drive, SAE A, 11 tooth
  • General
    • Vibration damper
    • Paint — Cat yellow
    • Lifting eyes
    • Automatic variable timing, electronic
    • Electronic installation kit 70-pin connector (connectors, pins, sockets)
    • Literature group owner and operator
  • Mandatory Options
    • Throttle position sensor
    • Exhaust system — front or rear
    • Flywheel housing or rear PTO
    • Primary filter/water separator
  • Transmission Arrangement
    • Transmission cooler
    • Tool set
  • Air Compressor
    • Air chambers
    • Air compressor governor
  • Air Inlet System
    • Air cleaners
    • Precleaners
    • Air lines
    • Air inlet gasket
  • Charging System
    • Charging alternators
    • Alternator mountings
    • Alternator wiring
    • Circuit breaker mountings
    • Alternator belt guard
  • Cooling System
    • Radiator — installed
    • Radiator — ship loose
    • Fan drive f/u/w Caterpillar installed radiator
    • Fan drives for customer-supplied radiators
    • Fan height instructions
    • Vee belts for customer-supplied radiators
    • Aftercooler lines f/u/w Caterpillar installed radiator
    • Rear-facing exhaust
    • Aftercooler lines
    • Suction fan adapters — attaches fan to fan pulley
    • Blower fan adapter — attaches fan to fan pulley
    • Blower fan
    • Suction fan
    • Fan belt tightener
    • Coolant level sensor
    • Dry charge coolant conditioners
    • Dry charge coolant conditioner element
  • Exhaust System
    • Turbo exhaust connection
    • Flexible fitting
    • Elbows
    • Flanges
    • Dry elbow