Piscataway Campus
732-885-5555
Bensalem Campus
877-726-7663

Oil and Gas

C32 ACERT™ Hazardous Location Engine

  • Maximum Rating
    1110 BHP
  • Displacement
    1960 in³
  • Minimum Rating
    800 BHP
  • Aspiration
    Turbocharged-Aftercooled
General Specifications
Maximum Rating
1110 BHP
Displacement
1960 in³
Minimum Rating
800 BHP
Aspiration
Turbocharged-Aftercooled
Flywheel and Flywheel Housing
SAE No. 0 or SAE No. 1
Flywheel Teeth
136
Stroke
6.4 in
Bore
5.7 in
Emissions
Emissions
U.S. Non-Road Tier 2 CARB, IMO Tier II, EPA Marine Tier 2
Dimensions
Length
76.18 in.
Length
76.18 in
Width
56.34 in.
Width
56.34 in
Height
54.66 in.
Height
54.66 in
Weight
6950.0 lb
Weight
6950 lb
  • Air Inlet System
    • Dual side-mounted turbochargers — inlet 152.4 mm (6 in) hose connection
  • Control System
    • Programmable ratings
    • Cold mode start strategy
    • Automatic altitude compensation
    • Power compensation for fuel temperature
    • Programmable low and high idle
    • Electronic diagnostics and fault logging
    • Engine monitoring and protection system (speed, temperature, pressure)
    • J1939 Broadcast (diagnostic, engine status and control)
    • Electronic governing, PTO speed control
    • Certified electrical control system
    • Customer interface harness available as optional attachment
  • Cooling System
    • Thermostats and housing — outlet LH vertical orientation
    • Jacket water pump — gear-driven, centrifugal, RH
  • Exhaust System
    • Exhaust manifold, water-cooled
    • Dual turbo, rear turbo exhaust, full marmon connection 127 mm (5 in), maximum load 10 kg for direct connection to turbo
    • Water-cooled center sections
  • Flywheels and Flywheel Housing
    • Mandatory selection of: SAE No. 0 or SAE No. 1 flywheel and housing SAE standard rotation
  • Fuel System
    • MEUI fuel system
    • Fuel filter — RH (2 micron high performance)
    • Fuel transfer pump
    • Fuel priming pump
  • Lube System
    • Crankcase breather — rear-mounted
    • Oil cooler — RH
    • Oil filler in RH front gear case
    • Oil filter — RH
    • Oil level gauge — RH
    • Oil pan rear sump
  • Mounting System
    • Narrow front support
  • Power Take-Offs
    • Crankshaft pulley — 203.2 mm (8 in) 5 grooves 15.9 (.63 in) wide; 292.1 mm (11.5 in) 1 groove 15.9 (.63 in) wide
  • General
    • Paint — Cat yellow
    • Vibration damper with single pulley
    • Lifting eyes
    • Automatic variable timing — electronic
    • Electronic installation kit 70-pin connector (connectors, pins, socket)
  • Mandatory Options
    • HP must be specified when ordering
    • All engines shipped at 2100 rpm
    • Flywheel housing
    • These engines meet the current IMO emission standards as defined by Regulation 13 of Annex VI to the International Convention for the Prevention of Pollution from Ships, 1973, as modified by the Protocol of 1978, further amended by the Protocol of 1997. A statement of compliance issued by the United States government's EPA (Environmental Protection Agency) is included in the technical file that is shipped with the engine as proof of our engine's ability to meet IMO emissions requirements. If this technical file is insufficient to meet the customer's requirements, then a GL or CCS IMO emissions certification may be ordered.
  • Air Inlet System
    • Air cleaner
    • Air inlet adapters
    • Turbocharger outlet adapters
    • Air lines
  • Charging System
    • Battery chargers
    • Charging alternators
    • Alternator mounting
    • Circuit breakers and mountings
  • Cooling System
    • Dry charge coolant conditioners
    • Thermostat housing
    • Coolant level sensor
    • Radiator
    • Suction fans and blower fans
    • Fan adapters
    • Fan drives
  • Emissions
    • IMO certifications
  • Exhaust System
    • Elbows
    • Mufflers
  • Fuel Systems
    • Electric fuel priming pump
  • Instrumentation
    • Customer management device
    • Interconnect harness
    • Gauges and instrument panels
  • Lube System
    • Oil pans
    • Oil service side
    • Oil level gauge
    • Oil filters
    • Lubricating oils
  • Mounting System
    • Structural steel base
    • Engine support — front and rear
  • Power Take-Offs
    • Auxiliary drive
    • Damper pulley
    • Hydraulics gear pumps
  • Protection System
    • Mechanical shutoffs
    • Solenoid shutoffs
  • Starting System
    • Electric starting motors - 12V, 24V
    • Battery sets - 24V
    • Battery rack and cable
    • Starting aids
  • Transmission Arrangement
    • Transmission water lines
    • Transmission cooler